Understanding Plumbing Basics for Bathtub Installation
Understanding Plumbing Basics for Bathtub Installation
Blog Article
We have found this post involving How to Install a Bathtub Yourself below on the web and think it made sense to relate it with you on this page.
Mounting a bath tub isn't precisely brain surgery, however it does need solid plumbing, carpentry, and sometimes, tiling skills. Changing an old bathtub with a new one is likewise a moderately difficult task. If the old tub is easily accessible, the project can move easily; if you have to open up a wall to get rid of the old tub and also place the new bath tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will require a helper to vacate the old tub as well as embeded in the new one. See to it you have certified on your own for the job and also are comfortable trying it. Instead of hiring a service provider to take control of a halfway-completed job, it is much better to take into consideration employing one prior to you start. Chances are you might require an expert plumber to make tube links.
This post will aid you set up a brand-new tub in your restroom if you have already bought a brand-new bathtub as well as do not require to change the plan of your previous supply of water pipelines.
Your tools as well as product checklist must consist of the following:
Getting ready for the Installation
To start with, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps device to stop stress on the tub.
Fit the adaptable faucet connectors to the bottom of both taps utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you use all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its last placement.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you need to do is detach the water. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be quite bothersome as a result of the restricted accessibility that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will originate from the pipes. As soon as the supply pipes have actually been removed, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to proceeding to fit the new taps, contrast the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Making use of both wood boards under its feet, place the bathtub in the called for placement. The wooden boards are practical in evenly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub till the spirit level reads degree.
To mount faucets, fit the bottom of the outermost versatile tap adapter to the ideal supply pipe by making a compression join; after that do the same for the various other faucet.
Switch on the water as well as examine all joints as well as brand-new pipework for leaks as well as tighten them if required. Load the tub as well as likewise examine the overflow electrical outlet as well as the regular outlet for leaks.
Finally, deal with the bath paneling as explained in the supplier's instruction manual. Tiling and also sealing around the bath tub must wait until the bathtub has actually been used a minimum of once as this will settle it into its final position.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet and the sink. Protect the faucet in place with the manufacturer offered backnut. When the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The former type ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to break a rigid seal, causing the water to penetrate the wall between the bathroom and also the tiling, bring about difficulties with moisture and possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water before securing, to allow for the activity experienced when the bathtub remains in use. The sealant can fracture relatively early if you do not take into account this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that write-up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from an associate on another web address. If you enjoyed our blog post plz make sure you remember to share it. Thank you for taking the time to read it.
Reliable every time! Report this page